“紫色”词汇中英文对照
“紫色” purple ;violet 紫罗兰色 violet
紫水晶色 amethyst
葡萄紫 grape
玫瑰紫 rose violet
丁香紫 lilac
墨紫 violet black
绛紫 dark reddish purple
暗紫 violet deep; dull purple
乌紫 raisin
蓝紫 royal purple
鲜紫 violet light
深紫 Modena
浅紫 grey violet
淡紫 pale purple ;lavender
淡白紫 violet ash
青莲 heliotrope
雪青 lilac
墨绛红 purple black
暗绛红 purple deep
浅绛红 purple light
QC缩写
QCquality control品质管理人员
FQCfinal quality control终点品质管制人员
IPQCin process quality control制程中的品质管制人员 OQCoutput quality control最终出货品质管制人员IQCincoming quality control进料品质管制人员 TQCtotal quality control全面质量管理
POCpassage quality control巡检人员
QAquality assurance质量保证人员
OQAoutput quality assurance出货质量保证人员QEquality engineering品质工程人员
品质保证类
FAIfirst article inspection新品首件检查
FAAfirst article assurance首件确认
TVRtool verification report模具确认报告
3B3B模具正式投产前确认
CPcapability index能力指数
CPKcapability index of process模具制程能力参数SSQAstandardized supplier quality合格供应商品质评估OOBAout of box audit开箱检查
QFDquality function deployment品质机能展开
FMEAfailure model effectiveness analysis失效模式分析8 disciplines8项回复内容
FAfinal audit最后一次稽核
CARcorrective action request改正行动要求corrective action report改正行动报告
FQC运作类
AQLAcceptable Quality Level运作类允收品质水准S/SSample size抽样检验样本大小
ACCAccept允收; REEReject拒收 ;CRCritical极严重的; MINMinor轻微的
AOQAverage Output Quality平均出厂品质
AOQLAverage Output Quality Level平均出厂品质Q/R/SQuality/Reliability/Service品质/可靠度服务MIL-STDMilitary-Standard军用标准
S I-S IVSpecial I-Special IV特殊抽样水准等级 P/NPart Number料号
L/NLot Number批号
AODAccept On Deviation特采
UAIUse As It首件检查报告MAJMajor主要的
FPIRFirst Piece Inspection Report首检报告
PPMPercent Per Million百万分之一
制程统计品管专类
SPCStatistical Process Control统计制程管制
SQCStatistical Quality Control统计品质管制
RRange全距
ARAverary Range全距平均值
UCLUpper Central Limit管制上限
LCLLower Central Limit管制下限
MAXMaximum最大值
MSA,FMEAMINMinimum最小值
GRRGauge Reproducibility&Repeatability量具之再制性及重测性
DIMDimension尺寸 ;DIADiameter直径 ;FREQFrequency频率; NNumber样品数
其它品质术语类QCCQuality Control Circle品质圈
QITQuality Improvement Team品质改善小组
PDCAPlan Do Check Action计划 执行 检查 总结
ZDZero Defect零缺点
QIQuality Improvement品质改善
QPQuality Policy目标方针
TQMTotal Quality Management全面品质管理
MRBMaterial Reject Bill退货单
LQLLimiting Quality Level最低品质水准
RMAReturn Material Audit退料认可
QANQuality Amelionrate Notice品质改善活动
ADMAbsolute Dimension Measuremat全尺寸测量
QTQuality Target品质目标
7QCTools7 Quality Controll Tools品管七大手法
通用之件类
ECNEngineering Change Notes工程变更通知(供应商)
ECOEngineering Change Order工程改动要求(客户)
PCNProcess Change Notice工序改动通知
PMPProduct Management Plan生产管制计划
SIPSpecification In Process制程检验规范 (检验作业指导书)
SOPStandard Operation Procedure标准作业指导书(生产)
ISInspection Specification成品检验规范
BOMBill Of Material物料清单
PSPackage Specification包装规范
SPECSpecification规格
SHIPPER---发货人...
CONSIGNEE--收货人...
货代常用英文
(一) 船代
Shipping agent 船舶代理
Handling Agent 操作代理
Booking Agent 订舱代理
Cargo Canvassing 揽货
FFF: Freight Forwarding Fee 货代佣金
Brokerage / Commission 佣金
(二)订舱
Booking 订舱
Booking Note 订舱单
Booking Number 订舱号
Dock Receipt 场站收据
M/F (Manifest ) :a manifest that lists only cargo, without freight and charges 舱单Cable/Telex Release 电放
A Circular Letter 通告信/通知书
PIC: Person in Charge 具体负责操作人员
The said party 所涉及的一方
On Board B/L: On Board提单 A B/L in which a carrier acknowledges that goods have been placed on board a certain vessel。Used to satisfy the requirements of a L/CCancellation 退关箱
(三)港口
BP Base Port 基本港
Prompt release 即时放行
Transit time 航程时间 / 中转时间
Cargo availability at destination in 货物运抵目的地
Second Carrier (第)二程船
In transit 中转
Transportation hub 中转港
(四)拖车
Tractor 牵引车/拖头
Low-bed 低平板车
Trailer 拖车
Transporter 拖车
Trucking Company 车队(汽车运输公司)
Axle load 轴负荷
Tire-load 轮胎负荷
Toll Gate 收费口
(五)保税
Bonded Area 保税区
Bonded Goods ( Goods in Bond) 保税货物
Bonded Warehouse 保税库
Caged stored at bonded warehouse 进入海关监管
Fork Lift 叉车
Loading Platform 装卸平台
(六)船期
A Friday(Tuesday / Thursday)sailing 周五班
A fortnight sailing 双周班
A bi-weekly sailing 周双班
A monthly sailing 每月班
On-schedule arrival / departure 准班抵离
ETA :Estimated(Expected) Time of Arrival 预计到达时间
ETB: Estimated(Expected)Time of Berthing 预计靠泊时间
ETD Estimated(Expected) Time of Departure 预计离泊时间
The sailing Schedule/Vessels are subject to change without prior notice。 船期/船舶如有变更将不作事先通知
Closing Date:截止申报时间
Cut-off time:截关日
(七)费用
Ocean Freight 海运费
Sea Freight 海运费
Freight Rate 海运价
Charge / Fee (收)费
Dead Freight 空舱费
Dead Space: Space in a car, truck, vessel, etc., that is not utilized 亏舱
Surcharge / Additional Charge 附加费
Toll 桥/境费
Charges that are below a just and reasonable level 低于正当合理的收费
Market Price Level 市场价水平
Special Rate 特价
Rock Bottom Price 最低底价
Best Obtainable Price 市场最好价
CC Freight to Collect 到付运费
Freight Payable At Destination 到付运费
Back Freight 退货运费
Fixed Price 固定价格
Comm. Commission 佣金
Rebate 回扣/折扣
Drayage charge: made for local hauling by dray or truck 拖运费
GRI :General Rate Increase 运价上调
SGRI :Second General Rate Increase 第二次运价上调
GRD :General Rate Decrease 运价下调
TGRD :Temporary General Rate Decrease 临时运价下调
PSS :Peak Season Surcharge 旺季附加费
Wharfage: A charge assessed by a pier against freight handled over the pier 码头附加费THC :Terminal Handling Charge 码头操作附加费
ORC :Origin Receiving Charge 始发接单费
CUC :Chassis Usage Charge 拖车运费
IAC :Inter-modal Administrative Charge(U.S. Inland Surcharge) 内陆运输附加费DDC :Destination Delivery Charge (目的地卸货费)
OAC: Origin Accessory Charge 始发港杂费
MAF: Manifest Amendment Fee 舱单改单费
(八)
For prompt shipment 立即出运
Cargo Supplier (供)货方
Upcoming Shipment 下一载货
Same Assignment 同一批货
Nomination Cargo 指定(指派)货
Indicated / Nominated Cargo 指装货
Shipments under B/L No。XXX XXX提单货
Cargo Volume 货量
Freight Volume 货量
Reefer Cargo 冷冻货
High-value Cargo (goods) 高价货
Miss Description 虚报货名
Agreement Rate 协议运价
D & H dangerous and hazardous 危险品
(九)单证
S/O Shipping Order 托(运)单
B/L Bill of Lading 提单
B/L Copy 提单副本
OBL Ocean Bill of Lading 海运提单
HBL House Bill of Lading 无船承运人提单
TBL Through Bill of Lading 全程提单
Advanced BL Advanced Bill of lading 预借提单
Anti-Dated BL Anti-dated Bill of Lading 倒签提单
Blank BL Blank Bill of Lading 空白提单
‘To Order’B/L 指示提单
Combined Bill 并单(提单)
Separate Bill 拆单(提单)
Straight B/L: A non-negotiable B/L。the Pomerene Act governs its operation in the US。 记名提单
On Board B/L :A B/L in which a carrier acknowledges that goods have been placed on board a certain vessel。Used to satisfy the requirements of a L/C =On Board提单
Shipped B/L: A B/L issued only after the goods have actually been shipped on board the vessel,as distinguished from the received for Shipments B/L 已出运的货物提单 (On Board B/L; Shipped B/L 已装船提单 )
Received for Shipment B/L 备运提单
Transhipment B/L 转船提单
Through B/L 联运提单
Shipper(Consignee)Box 发(收)货人栏(格)
Arrival Notice 到货通知书:An advice that the carrier sends to the consignee advising of goods coming forward for delivery. Pertinent information such as BL No.,container No. and total charge due from consignee, etc, are included and sent to consignee prior to vessel arrival. This is done gratuitously by the carrier to ensure smooth delivery but there is no obligation by the carrier to do so. The responsibility to monitor the transit and present himself to take timely delivery still rests with the consignee.
M/F: Manifest document that lists in detail all the Bs/L issued by a vessel or its agent or master,ie,a detailed summary of the total cargo 舱单
Batch Filing 批量报备
Manifest Discrepancy 舱单数据不符
Acknowledgement of Manifest Receipt 收到舱单回执
Packing List 装箱单
Cargo Receipt 承运货物收据
D/R Dock Receipt 场站收据
D/O Delivery Order 交货单(小提单)
Shipper’s Export Declaration 货主出口申报单
Shipping Advice 装运通知(似舱单 NVOCC用)
Manifest information 舱单信息
FCN Freight Correction Notice 舱单更改单(通知)
Surrender O B/L copies for consignment 交回提单副本
Release Note receipt signed by customer acknowledging delivery of goods 货物收讫单
(九)Inspection-related Terms 检验相关术语
Customs Inspection 海关查验
Commodity Inspection 商品检验
Tally 理货
Tally Report 理货报告
Check 查验/检查/核对
Fumigation:熏蒸
Animal / Plant Inspection 动植物检验
INSP Inspection / Inspector 检验/检验员
Certificate of Origin ( normally issued or signed by a Chamber of
Commerce or Embassy ) (始发地)原产地证书
Arbitration 仲裁
ACH :Automated Clearing House ( part of ACS ) 自动清关
AMS :Automated Manifest System ( for anti-terrorism ) 自动舱单(反恐)申报系统CSS :Cargo Selectivity System 货物抽验
CHB :Customs House Broker 报关行
SED :(EX-DEC) Shipper’s Export Declaration 货主出口报关单
BONDED WAREHOUSE 保税库
BONDED AREA 保税区
BONDED GOODS 保税货物
QUOTAs Quantity of one HTS item allowed to be imported at either higher or lower rate of duties. 进口配额
DDP: Delivery Duty Paid 完税
DDU: Delivery Duty Unpaid 未完税
DRAWBACK: Duties payment refunded because freight is re-exported or for similar circumstances 退税金额
Customs fine 海关罚款
Customs seals 海关关封
Application for inspection 检验申请
To expedite the clearance 加快清关
Pilferage 盗窃/偷窃
To be liable for a penalty of 受到。。。处罚
Non-fraudulent violation of the regulation 非故意违反规定
To file certifications with Customs 向海关申报有效证明
To follow the current procedure 遵循现行程序
To abide by 。。。rule 遵照。。。规定
To provide specific language 提供一定说法
To be not authorized 不予认可
(十)箱子
COC Carrier’s Own Container(CARRIER OWNED CTN) 船东自有箱
Container Cleaning 洗箱
VEN Ventilated 通风
FRZ Frozen 冰冻
HTD Heated 加热
I.D. Inside Dimension 箱内尺码
Inside Measurement 箱内尺码
TW ( TARE WEIGHT ) The weight of an empty container 箱子皮重Container Leasing Co。 租箱公司
Equipment Exchange (Interchange) Receipt 设备交接单
Repositioning 集装箱回空
Container Leasing long-term / short-term lease 集装箱租赁 长期 / 短期Leasing Company 租箱公司
premises for longer period than provided in Tariff 空箱滞箱费Demurrage 重箱滞箱费
厨柜英语Kitchen Cabinet
灯线脚线脚线高度Light/lamp kick Toe kick Toe height
地柜吊柜高柜半高柜其它灯具水槽电器水龙头
下水器封板双层餐具垃圾桶垃圾篮
层板粒上翻门灯具变压器
转向灯变压器拉篮见光贴面吊轨喷口微波炉烤箱油烟机燃气炉电磁炉
结构: 屋顶墙面台面直径后面底部平面立面侧面背面平面图正面图立面图
折角
English
配同门板色脚线 concolor toe kick 柜子前边缘Carcase Front Edge Basecabinet/Unit 中间开
Center separate
Wallcabinet/Unit
Tallcabinet/Unit 板材: Semi-tall cabinet 原木lumber miscellaneous 实木solid wood light 橡木oak sink 桦木
birch appliances 橡胶木Rubber wood Faucet 贴橡木皮
oak veneer bottle tap 夹板,胶合板Plywood filler panel
爱家板MFC board 2-tier cutlery tray 中纤板MDF Board waste bin
海木板Seawood board cleaning material basket 防火板
Fireproof board
supports 防潮板Damp proof board
flap-up door
刨花板(PB) Particle board / Chipboard transformer for integrated light PVC吸塑PVC Membrane transformer for volatage halogen
pull-out basket 平板
flat sheet
finished side波形板roofing sheet mounting track 门板Door Panel pull-out spout 顶板 /天板 Top Panel/Board microwave 面板Faceplate oven 前板Front Panel
chimney hood 侧板Side Panel
burner
背板Back Panel / Rear Panel ceramic hob
底板
Base Panel / Bottom Board 加高侧板The raised Box Side 名牌
Name plate roofing
层板Shelf Board fasade
活板Movable Board Counter top 固定板Fix Board Diameter 补强板Support Board Rear 直边板
Wood end panel
Base 支撑挂板Support Plate
Plan 裙角Bottom Front Board Elevation 桶侧Drawer Side Board Side Elevation 桶尾Drawer Back Board Back Elevation 桶里板
Drawer Inner Board Floor Plan
抽屉面/桶面/桶头 Drawer Front Panel Front Elevation 灯板lamp panel Sectional Elevation 见光Exposed panel 假门Fake Door Panel Dog Ear
假门板
Fake panel
薄板,胶合板,镶板 饰面板水晶板柜身板柜身材料人造石高压板门不锈钢背板门: 趟门玻璃门 感应门 滑板门 框线门 百叶门 折叠门 伸缩门 镜面门 模压门 卷帘门 遮阳门
Veneer
veneer board crystal board Carcase Panel Carcase Material acrylic artificial board High Pressure Laminate Stainless steel back panel Filler
散热器壁挂锅炉水过滤器radiator
wall-hung boiler water filter
fuel oil filter
food waste disposer
燃油过滤器食物垃圾处理机
配件: 炉柜
Shelve case
integral kitchen cabinet cabinet combination Tier kitchen Work station Wash Platform Heating Platform Seasoning Platform Preparation Platform Home step chair Pantry Dresser rattan stair mattress Drawer gatter / sink Sink Sink case Wash Basin Wine rack hanging basket Pull-out Basket Sliding Basket radiator
Bottle Carrier Basket door bell
Side Mounted Organizer Plastic rubbish bin
Door mounted Rubbish Bin gas water heater noiseless ventilation fan kitchen wire rack
填充物,封板
集成橱柜整体橱柜
Sliding Door Glass Door sensor door sliding door framed door Louver Door Folding Door retractile door Door with Mirror molding press door Roller Shutter Door sunshine-shading shed
Display Door
Upturn and Paralleled Motion Door
叠层厨房用具办公台清洗台加热台 调料台
准备台家庭用梯台 食品柜梳妆台 藤楼梯床垫抽屉
陈列式门上翻平移门帘: 百叶帘 垂直帘 天幕帘 屏风帘 罗马帘 卷帘卷帘窗
电器: 冰箱洗碗机 烘碗机 洗衣机 洗衣机 电烤箱 炉头烧烤炉 微波炉
水槽水池,水槽水盆柜 星盆酒架挂蓝拉篮滑篮暖气片 提瓶架
louver vertical blind skylight system panel screen roman blind roller blind rolling window
谐音门铃侧式拉架胶垃圾柜内置垃圾桶 燃气热水器
Refrigerator freezer Dishwasher dish drier Washer dryer washing machine oven
Gas range oven barbeque oven Microwave oven hood
cooker / rangehood cooker&hob
静音换气扇厨房多用拉篮
家庭采暖系统home heating system 自动上翻门折叠支架
Automatic Upward-Turning Folding Door Bracket 厨房遥控开降台 Remote Control Lifting Platform 槽Grooves 水漏流槽弯关浴镜浴架
waste Vanner siphon Mirror Shelf
烟机排油烟机灶具
燃气灶gas cooker / gas stove
燃气/燃木/电壁炉gas fired / wood fired / electric fireplace
浴灯皂碟隔断浴柜悬垂衣帽间 浴帘布 浴帘杆 感应灯 落水管 落水器 排水器 下水弯 马桶盖 感应器
Light
Soap dish partition
Bath vanity/case Granite Top Overhang cloakroom shower curtain shower curtain bar Sense Light downpipe waste kits draining pipetrap toilet seat inductor
veneer Vanity
Tall Bath cabinet/tall case Light Valance
rotating clothes-rack illumination switch marble crystal stone quartz
lawn and garden paint and coatings aluminium rack sealant strip
rubber hose rubber gasket
rubber profile material glass frame glass basin tempered glass bended glass Suspension Fittings Dust Seal Rail handle armrail
Carre Handle
96MM亚光月亮抽 96MM Mat Finish Half moon Handle 空心拉杆抽,银色拱桥抽
Hollow handle / bridge shape silver handle 钻孔Drill 滚珠Roll Bearing 灰圆杆灰圆杆接头 花岗石,颗粒 滑轨 ,趟路 曲路滑轨
Gross Galley Rail
Gross Gallery Connector Granite
Runner / slideStraight Rail
Drawer Side with Runner
Bottom Mounting Drawer Runner Two Wheel Guiding Fittings
抽屉侧板滑轨托底式抽屉滑轨 双轮滑动部件
滑轨安装及间隙尺寸
Dimension of Drawer Runner Installation 无声滚珠轴承Silence Ball Bearing 上轨道Top Rail 下轨道Bottom Rail 胶趟路五金(铁)趟路
铰链烟斗铰
Plastic Rail Metal Rail Hinge
Sliding Hinge
Material of Hinges Cup Zinc-alloy Concealed Hinge Rolled Hinge Fold Table Hinge
Material of Hinges Arm
45 Angle Hinge
Rapid Assembly Concealed Hinge Hydraulic-Pressure Buffering Hinge Nut
贴面纸盥洗盆,浴柜高身浴柜灯饰,灯幔旋转衣架照明开关
大理石
水晶石石英刚石草坪及园艺 油漆涂料
铝架密封条
铰杯材料合金暗铰反扣铰链翻转合叶铰臂材料
45度铰链快速暗铰铰链液压缓冲铰链
螺母
橡胶管橡胶垫圈橡胶型材
玻璃框
插销 ,螺钉 螺杆底座预埋螺母定位螺丝自攻螺丝螺钉盖板可拆卸螺丝
BoltScrew Seat
Glued Socket Locating Screw Fastening Screw Screw Cover Board Comb lock screw
玻璃台面强化玻璃弯曲玻璃
吊码
防尘条栏杆,扶手 拉手扶手摞抽
水平调节螺丝Depth Adjustment Screw 十字尖头螺丝Cross Nibbed Screw 没有弹弓式的天花螺丝No spring type bolt
明装暗装嵌门式 盖门式
Showing Installation Insert Installation Insert Overlay Type Rapid Installation Half-Overlay
桶条抽Metal Handle 黑底银面凹抽Silver Concave Handle BK Base 扁平抽(平面抽) Metal Plate Handle 银色空心拉杆抽 96MM桥形银抽
Silver Hollow Metal Handle
96MM Bridge Shape Silver Handle
快装式半盖门式
万向轮侧向调节前后调节垂直调节
滚轮插轮铁板轮
孔塞
Free Direction Wheel Side Adjustment Depth Adjustment Vertical Adjustment Caster Insert Type Caster Metal Plate Caster Trim Caps Ventilate Trim Caps Bracket Sandblast Support Bar Edge Banding Matt Oxidation Revolver fitting Loading Capacity Buffer
Fixed Seat Glass Clips Clean ability
Wear Resistance Rear Panel Hook Cabinet Adjusting Leg Opening Angle Silence Design Guiding Fitting Cabinet Support Polished Oxidation Full-Stage Damper Carcase Wrench
美背美边侧板孔位钻穿强化纸,普通纸2面贴纸+菲林边 包装尺寸完成后尺寸 单坑箱单坑箱包装
PVC edge: front and back 2 way pin hole for movable BD Hard paper/ normal paper paper in 2 faces and tensha edge Packing size
Finished size
Single ply corrugated box
Packed by 1 PLY corrugated carton
装载量:400套/40柜 Load ability: 400sets/40 两个一套,一个一包
Each in a carton, 2 cartons for 1 completed unit
盐田离岸价FOB Yan Tian 海运差价Ocean freight charge difference 日本主要港口到岸价C&F Japanese main port
拖车仲裁收货人 发货人
Haulage Arbitration
Consignee
Shipper,Consignor Port of LoadingPlace ofDelivery Local charge
Force Majeure
Act of god usual force majeure Fumigation CertificateInspection Claims
DOC=Direct Operating Cost
透气孔塞托架喷砂驳条封边磨沙转架承重缓冲器 固定座 玻璃夹 耐污渍 耐磨损 背板扣 调节脚
起运港交货地当地杂费不可抗力不可抗力clause 熏蒸证明检验与索赔
机器名称: 三片锯开料锯
热压机 压板机 排钻机 弯边机 包覆机 复合机 封边机
开启角度消音设计导向部件厨柜气撑亮光氧化全程缓冲框架,架子扳手,钳子刹制 /阻尼 金属连接件 偏心连接件 台面升降器 门板孔位图
直接操作费用
Three Rip Saw
Material Handling Machine Hot-Presser Veneer Press Boring Machine Bending Machine Sheathing Machine Compound Machine
Bender
(Single-sided
or
StopperSteel Joint Connector
Eccentric Connection Part Table Top Elevating Fitting Hole Position of the Door Carrying Capacity of Double Form of Fastness of Rail’s Caput Dowel
每对承载力定轨头部形状暗销,木钉,销子上下推拉门配件
电线圈
Edge
Pushing from Top to Bottom Fitting for Sliding Doors
Wire Holder
Two Head Socket One Head Socket
2 heads socket with cable: 1 pc Push Pin
double-sided) 传统刨花机电脑成型机 电脑裁板机
Router
N.C Router
Computer Board Cutter Vacuum Membrane Press Multi-Axle Vertical Puncher Auto-Shaper
双头电线单头电线双头电线插座
弹弓门卒
真空吸塑机多轴水平钻孔机 自动立轴成型机
双向(水平及垂直)三面钻孔机
Dual Direction (horizontal and vertical) three-side puncher
初等数学 elementary mathematics 高等数学 higher mathematics 现代数学 modern mathematics 基础数学 basic mathematics 应用数学 applied mathematics 计算数学computational mathematics 复变函数论 theory of functions of a complex variable 实变函数论 theory of functions of a real variable 泛函分析 functional analysis 数理逻辑 mathematical logic 数理统计 mathematical statistics 常微分方程 ordinary different
数学 mathematics, maths(BrE), math(AmE) 公理 axiom 定理 theorem 计算 calculation 运算 operation 证明 prove 假设 hypothesis, hypotheses(pl.) 命题 proposition
算术 arithmetic 加 plus(prep.), add(v.), addition(n.) 被加数 augend, summand 加数 addend 和 sum 减 minus(prep.), subtract(v.), subtraction(n.) 被减数 minuend 减数 subtrahend 差 remainder 乘 times(prep.), multiply(v.), multiplication(n.) 被乘数 multiplicand, faciend 乘数 multiplicator 积 product 除 divided by(prep.), divide(v.), division(n.) 被除数 dividend 除数 divisor 商 quotient 等于 equals, is equal to, is equivalent to 大于 is greater than 小于 is lesser than 大于等于 is equal or greater than 小于等于 is equal or lesser than 运算符 operator 数字 digit 数 number 自然数 natural number 整数 integer 小数 decimal 小数点 decimal point 分数 fraction 分子 numerator 分母 denominator 比 ratio 正 positive 负 negative 零 null, zero, nought, nil 十进制 decimal system 二进制 binary system 十六进制 hexadecimal system 权 weight, significance 进位 carry 截尾 truncation 四舍五入 round 下舍入 round down 上舍入 round up 有效数字 significant digit 无效数字 insignificant digit
代数 algebra 公式 formula, formulae(pl.) 单项式 monomial 多项式 polynomial, multinomial 系数 coefficient 未知数 unknown, x-factor, y-factor, z-factor 等式,方程式 equation 一次方程 simple equation 二次方程 quadratic equation 三次方程 cubic equation 四次方程 quartic equation 不等式 inequation 阶乘 factorial 对数 logarithm 指数,幂 exponent 乘方 power 二次方,平方 square 三次方,立方 cube 四次方 the power of four, the fourth power n次方 the power of n, the nth power 开方 evolution, extraction 二次方根,平方根 square root 三次方根,立方根 cube root 四次方根 the root of four, the fourth root n次方根 the root of n, the nth root 集合 aggregate 元素 element 空集 void 子集 subset 交集 intersection 并集 union 补集 complement 映射 mapping 函数 function 定义域 domain, field of definition 值域 range 常量 constant 变量 variable 单调性 monotonicity 奇偶性 parity 周期性 periodicity 图象 image 数列,级数 series 微积分 calculus 微分 differential 导数 derivative 极限 limit 无穷大 infinite(a.) infinity(n.) 无穷小 infinitesimal 积分 integral 定积分 definite integral 不定积分 indefinite integral 有理数 rational number 无理数 irrational number 实数 real number 虚数 imaginary number 复数 complex number 矩阵 matrix 行列式 determinant
几何 geometry 点 point 线 line 面 plane 体 solid 线段 segment 射线 radial 平行 parallel 相交 intersect 角 angle 角度 degree 弧度 radian 锐角 acute angle 直角 right angle 钝角 obtuse angle 平角 straight angle 周角 perigon 底 base 边 side 高 height 三角形 triangle 锐角三角形 acute triangle 直角三角形 right triangle 直角边 leg 斜边 hypotenuse 勾股定理 Pythagorean theorem 钝角三角形 obtuse triangle 不等边三角形 scalene triangle 等腰三角形 isosceles triangle 等边三角形 equilateral triangle 四边形 quadrilateral 平行四边形 parallelogram 矩形 rectangle 长 length 宽 width 菱形 rhomb, rhombus, rhombi(pl.), diamond 正方形 square 梯形 trapezoid 直角梯形 right trapezoid 等腰梯形 isosceles trapezoid 五边形 pentagon 六边形 hexagon 七边形 heptagon 八边形 octagon 九边形 enneagon 十边形 decagon 十一边形 hendecagon 十二边形 dodecagon 多边形 polygon 正多边形 equilateral polygon 圆 circle 圆心 centre(BrE), center(AmE) 半径 radius 直径 diameter 圆周率 pi 弧 arc 半圆 semicircle 扇形 sector 环 ring 椭圆 ellipse 圆周 circumference 周长 perimeter 面积 area 轨迹 locus, loca(pl.) 相似 similar 全等 congruent 四面体 tetrahedron 五面体 pentahedron 六面体 hexahedron 平行六面体 parallelepiped 立方体 cube 七面体 heptahedron 八面体 octahedron 九面体 enneahedron 十面体 decahedron 十一面体 hendecahedron 十二面体 dodecahedron 二十面体 icosahedron 多面体 polyhedron 棱锥 pyramid 棱柱 prism 棱台 frustum of a prism 旋转 rotation 轴 axis 圆锥 cone 圆柱 cylinder 圆台 frustum of a cone 球 sphere 半球 hemisphere 底面 undersurface 表面积 surface area 体积 volume 空间 space 坐标系 coordinates 坐标轴 x-axis, y-axis, z-axis 横坐标 x-coordinate 纵坐标 y-coordinate 原点 origin 双曲线 hyperbola 抛物线 parabola
三角 trigonometry 正弦 sine 余弦 cosine 正切 tangent 余切 cotangent 正割 secant 余割 cosecant 反正弦 arc sine 反余弦 arc cosine 反正切 arc tangent 反余切 arc cotangent 反正割 arc secant 反余割 arc cosecant 相位 phase 周期 period 振幅 amplitude 内心 incentre(BrE), incenter(AmE) 外心 excentre(BrE), excenter(AmE) 旁心 escentre(BrE), escenter(AmE) 垂心 orthocentre(BrE), orthocenter(AmE) 重心 barycentre(BrE), barycenter(AmE) 内切圆 inscribed circle 外切圆 circumcircle
统计 statistics 平均数 average 加权平均数 weighted average 方差 variance 标准差 root-mean-square deviation, standard deviation 比例 propotion 百分比 percent 百分点 percentage 百分位数 percentile 排列 permutation 组合 combination 概率,或然率 probability 分布 distribution 正态分布 normal distribution 非正态分布 abnormal distribution 图表 graph 条形统计图 bar graph 柱形统计图 histogram 折线统计图 broken line graph 曲线统计图 curve diagram 扇形统计图 pie diagram 方程
wave equation 波动方程 tangental equation 切线方程 quartic equation 四次方程式 quadratic equation 二次方程式 magnitude equation 【天】星等差 linear equation 一次方程式
irreducible equation 不可约方程 integral equation 积分方程
indicial equation 【数】指数方程 indeterminate equation 不定方程
集合与简易逻辑
集合(集)
set 非负整数集
the set of all non-negative integers 自然数集
the set of all natural numbers 正整数集
the set of all positive integers 整数集
the set of all integers 有理数集
the set of all rational numbers 实数集
the set of all real numbers 元素
element 属于
belong to 不属于
not belong to 有限集
finite set 无限集
infinite set 空集
empty set 包含
inclusion, include 包含于
lie in 子集
subset 真子集
补集(余集)
全集
交集
并集
偶数集
奇数集
含绝对值的不等式
一元二次不等式
逻辑
逻辑联结词
或
且
非
真
假
真值表
原命题
逆命题
否命题
逆否命题
充分条件
必要条件
充要条件
……的充要条件是……
函数
函数
自变量
定义域
值域
区间
闭区间
开区间
函数的图象
proper subset
complementary set universe intersection
union
the set of all even numbers
the set of all odd numbers
inequality with absolute value
one-variable quadratic inequality
logic
logic connective
or
and
not
true
false
truth table
original proposition
converse proposition
negative proposition
converse-negative proposition
sufficient condition
necessary condition
sufficient and necessary condition … if and only if …
function argument domain range interval
closed interval open interval graph of function
映射
mapping 象
image 原象
inverse image 单调
monotone 增函数
increasing function 减函数
decreasing function 单调区间
monotone interval 反函数
inverse function 指数
exponent n次方根
根式
根指数
被开方数
指数函数
对数
常用对数
自然对数
对数函数
数列
数列
项
通项公式
有穷数列
无穷数列
递推公式
等差数列
公差
等差中项
等比数列
公比
等比中项
三角函数
三角函数
始边
终边
正角
负角
零角
象限角
弧度
弧度制
n th root
radical
radical exponent
radicand
exponential function
logarithm
common logarithm
natural logarithm
logarithmic function
sequence of number
term
the formula of general term
finite sequence of number
infinite sequence of number
recurrence formula
arithmetic progression ,
arithmetic series
common difference
arithmetic mean
geometric progression,
geometric series
common ratio
geometric mean trigonometric function initial side terminal side positive angle negative angle zero angle quadrant angle radian
radian measure
角度制
degree measure 正弦
sine 余弦
cosine 正切
tangent 余切
cotangent 正割
secant 余割
cosecant 诱导公式
induction formula 正弦曲线
sine curve 余弦曲线
最大值
最小值
周期
最小正周期
周期函数
振幅
频率
相位
初相
反正弦
反余弦
反正切
平面向量
有向线段
数量
向量
零向量
相等向量
共线向量
平行向量
向量的数乘
单位向量
基底
基向量
平移
数量积
正弦定理
余弦定理
不等式
算术平均数
几何平均数
比较法
cosine curve maximum minimum period
minimal positive period periodic function
amplitude of vibration frequency phase
initial phase arc sine arc cosine arc tangent directed line segment scalar quantity vector zero vector equal vector collinear vectors parallel vectors
multiplication of vector by scalar unit vector base
base vectors translation inner product sine theorem cosine theorem
arithmetic mean
geometric mean
method of compare
综合法
method of synthesis 分析法
method of analysis 直线
倾斜角
angle of inclination 斜率
gradient 点斜式
point slope form 截距
intercept 斜截式
gradient intercept form 两点式
一般式
夹角
线性规划
约束条件
目标函数
可行域
最优解
圆锥曲线
曲线
坐标法
解析几何
笛卡儿
标准方程
一般方程
参数方程
参数
圆锥曲线
椭圆
焦点
焦距
长轴
短轴
离心率
双曲线
实轴
虚轴
渐近线
抛物线
准线
初等数学 elementary mathematics 高等数学 higher mathematics 现代数学 modern mathematics 基础数学 basic mathematics 应用数学 applied mathematics
two-point form general form included angle
linear programming constraint condition objective function feasible region optimal solution curve
method of coordinate analytic geometry Descartes
standard equation general equation parameter equation parameter point conic ellipse
focus, focal points focal length major axis minor axis eccentricity hyperbola real axis
imaginary axis asymptote parabola directrix
计算数学computational mathematics 复变函数论 theory of functions of a complex variable 实变函数论 theory of functions of a real variable 泛函分析 functional analysis 数理逻辑 mathematical logic 数理统计 mathematical statistics 常微分方程 ordinary differential equation 偏微分方程 partial differential equation 数理方程 equation of mathematical physics 代数拓扑学 algebraic topology 集合论 set theory 拓扑空间 topological 概率论 probability 随机过程 stochastic process 李群 Lie group 数论 number theory 图论 graph theory 编码理论 coding theory 混沌理论 chaotic theory 一般词汇
数学 mathematics, maths(BrE), math(AmE) 公理 axiom 定理 theorem 计算 calculation 运算 operation 证明 prove 假设 hypothesis, hypotheses(pl.) 命题 proposition
算术 arithmetic 加 plus(prep.), add(v.), addition(n.) 被加数 augend, summand 加数 addend 和 sum 减 minus(prep.), subtract(v.), subtraction(n.) 被减数 minuend 减数 subtrahend 差 remainder 乘 times(prep.), multiply(v.), multiplication(n.) 被乘数 multiplicand, faciend 乘数 multiplicator 积 product 除 divided by(prep.), divide(v.), division(n.) 被除数 dividend 除数 divisor 商 quotient 等于 equals, is equal to, is equivalent to 大于 is greater than 小于 is lesser than 大于等于 is equal or greater than 小于等于 is equal or lesser than 运算符 operator 数字 digit 数 number 自然数 natural number 整数 integer 小数 decimal 小数点 decimal point 分数 fraction 分子 numerator 分母 denominator 比 ratio 正 positive 负 negative 零 null, zero, nought, nil 十进制 decimal system 二进制 binary system 十六进制 hexadecimal system 权 weight, significance 进位 carry 截尾 truncation 四舍五入 round 下舍入 round down 上舍入 round up 有效数字 significant digit 无效数字 insignificant digit
代数 algebra 公式 formula, formulae(pl.) 单项式 monomial 多项式 polynomial, multinomial 系数 coefficient 未知数 unknown, x-factor, y-factor, z-factor 等式,方程式 equation 一次方程 simple equation 二次方程 quadratic equation 三次方程 cubic equation 四次方程 quartic equation 不等式 inequation 阶乘 factorial 对数 logarithm 指数,幂 exponent 乘方 power 二次方,平方 square 三次方,立方 cube 四次方 the power of four, the fourth power n次方 the power of n, the nth power 开方 evolution, extraction 二次方根,平方根 square root 三次方根,立方根 cube root 四次方根 the root of four, the fourth root n次方根 the root of n, the nth root 集合 aggregate 元素 element 空集 void 子集 subset 交集 intersection 并集 union 补集 complement 映射 mapping 函数 function 定义域 domain, field of definition 值域 range 常量 constant 变量 variable 单调性 monotonicity 奇偶性 parity 周期性 periodicity 图象 image 数列,级数 series 微积分 calculus 微分 differential 导数 derivative 极限 limit 无穷大 infinite(a.) infinity(n.) 无穷小 infinitesimal 积分 integral 定积分 definite integral 不定积分 indefinite integral 有理数 rational number 无理数 irrational number 实数 real number 虚数 imaginary number 复数 complex number 矩阵 matrix 行列式 determinant
几何 geometry 点 point 线 line 面 plane 体 solid 线段 segment 射线 radial 平行 parallel 相交 intersect 角 angle 角度 degree 弧度 radian 锐角 acute angle 直角 right angle 钝角 obtuse angle 平角 straight angle 周角 perigon 底 base 边 side 高 height 三角形 triangle 锐角三角形 acute triangle 直角三角形 right triangle 直角边 leg 斜边 hypotenuse 勾股定理 Pythagorean theorem 钝角三角形 obtuse triangle 不等边三角形 scalene triangle 等腰三角形 isosceles triangle 等边三角形 equilateral triangle 四边形 quadrilateral 平行四边形 parallelogram 矩形 rectangle 长 length 宽 width 菱形 rhomb, rhombus, rhombi(pl.), diamond 正方形 square 梯形 trapezoid 直角梯形 right trapezoid 等腰梯形 isosceles trapezoid 五边形 pentagon 六边形 hexagon 七边形 heptagon 八边形 octagon 九边形 enneagon 十边形 decagon 十一边形 hendecagon 十二边形 dodecagon 多边形 polygon 正多边形 equilateral polygon 圆 circle 圆心 centre(BrE), center(AmE) 半径 radius 直径 diameter 圆周率 pi 弧 arc 半圆 semicircle 扇形 sector 环 ring 椭圆 ellipse 圆周 circumference 周长 perimeter 面积 area 轨迹 locus, loca(pl.) 相似 similar 全等 congruent 四面体 tetrahedron 五面体 pentahedron 六面体 hexahedron 平行六面体 parallelepiped 立方体 cube 七面体 heptahedron 八面体 octahedron 九面体 enneahedron 十面体 decahedron 十一面体 hendecahedron 十二面体 dodecahedron 二十面体 icosahedron 多面体 polyhedron 棱锥 pyramid 棱柱 prism 棱台 frustum of a prism 旋转 rotation 轴 axis 圆锥 cone 圆柱 cylinder 圆台 frustum of a cone 球 sphere 半球 hemisphere 底面 undersurface 表面积 surface area 体积 volume 空间 space 坐标系 coordinates 坐标轴 x-axis, y-axis, z-axis 横坐标 x-coordinate 纵坐标 y-coordinate 原点 origin 双曲线 hyperbola 抛物线 parabola
三角 trigonometry 正弦 sine 余弦 cosine 正切 tangent 余切 cotangent 正割 secant 余割 cosecant 反正弦 arc sine 反余弦 arc cosine 反正切 arc tangent 反余切 arc cotangent 反正割 arc secant 反余割 arc cosecant 相位 phase 周期 period 振幅 amplitude 内心 incentre(BrE), incenter(AmE) 外心 excentre(BrE), excenter(AmE) 旁心 escentre(BrE), escenter(AmE) 垂心 orthocentre(BrE), orthocenter(AmE) 重心 barycentre(BrE), barycenter(AmE) 内切圆 inscribed circle 外切圆 circumcircle
统计 statistics 平均数 average 加权平均数 weighted average 方差 variance 标准差 root-mean-square deviation, standard deviation 比例 propotion 百分比 percent 百分点 percentage 百分位数 percentile 排列 permutation 组合 combination 概率,或然率 probability 分布 distribution 正态分布 normal distribution 非正态分布 abnormal distribution 图表 graph 条形统计图 bar graph 柱形统计图 histogram 折线统计图 broken line graph 曲线统计图 curve diagram 扇形统计图 pie diagram 方程
wave equation 波动方程 tangental equation 切线方程 quartic equation 四次方程式 quadratic equation 二次方程式 magnitude equation 【天】星等差 linear equation 一次方程式
irreducible equation 不可约方程 integral equation 积分方程
indicial equation 【数】指数方程 indeterminate equation 不定方程
集合与简易逻辑
集合(集)
set 非负整数集
the set of all non-negative integers 自然数集
the set of all natural numbers 正整数集
the set of all positive integers 整数集
the set of all integers 有理数集
the set of all rational numbers 实数集
the set of all real numbers 元素
element 属于
belong to 不属于
not belong to 有限集
finite set 无限集
infinite set 空集
empty set 包含
inclusion, include 包含于
lie in 子集
subset 真子集
proper subset 补集(余集)
complementary set 全集
universe 交集
intersection 并集
union 偶数集
奇数集
含绝对值的不等式
一元二次不等式
逻辑
逻辑联结词
或
且
非
真
假
真值表
原命题
逆命题
否命题
逆否命题
充分条件
必要条件
充要条件
……的充要条件是……
函数
函数
自变量
定义域
值域
区间
闭区间
开区间
函数的图象
映射
象
原象
单调
增函数
the set of all even numbers
the set of all odd numbers
inequality with absolute value
one-variable quadratic inequality
logic
logic connective
or
and
not
true
false
truth table
original proposition
converse proposition
negative proposition
converse-negative proposition
sufficient condition
necessary condition
sufficient and necessary condition … if and only if …
function argument domain range interval
closed interval open interval graph of function mapping image
inverse image monotone
increasing function
减函数
decreasing function 单调区间
monotone interval 反函数
inverse function 指数
exponent n次方根
n th root 根式
radical 根指数
radical exponent 被开方数
radicand 指数函数
exponential function 对数
常用对数
自然对数
对数函数
数列
数列
项
通项公式
有穷数列
无穷数列
递推公式
等差数列
公差
等差中项
等比数列
公比
等比中项
三角函数
三角函数
始边
终边
正角
负角
零角
象限角
弧度
弧度制
角度制
正弦
余弦
正切
logarithm
common logarithm
natural logarithm
logarithmic function
sequence of number
term
the formula of general term
finite sequence of number
infinite sequence of number
recurrence formula
arithmetic progression ,
arithmetic series
common difference
arithmetic mean
geometric progression,
geometric series
common ratio
geometric mean trigonometric function initial side terminal side positive angle negative angle zero angle quadrant angle radian
radian measure degree measure sine cosine tangent
余切
cotangent 正割
secant 余割
cosecant 诱导公式
induction formula 正弦曲线
sine curve 余弦曲线
cosine curve 最大值
maximum 最小值
minimum 周期
period 最小正周期
周期函数
振幅
频率
相位
初相
反正弦
反余弦
反正切
平面向量
有向线段
数量
向量
零向量
相等向量
共线向量
平行向量
向量的数乘
单位向量
基底
基向量
平移
数量积
正弦定理
余弦定理
不等式
算术平均数
几何平均数
比较法
综合法
分析法
直线
minimal positive period periodic function
amplitude of vibration frequency phase
initial phase arc sine arc cosine arc tangent directed line segment scalar quantity vector zero vector equal vector collinear vectors parallel vectors
multiplication of vector by scalar unit vector base
base vectors translation inner product sine theorem cosine theorem
arithmetic mean
geometric mean
method of compare
method of synthesis
method of analysis
倾斜角
angle of inclination 斜率
gradient 点斜式
point slope form 截距
intercept 斜截式
gradient intercept form 两点式
two-point form 一般式
general form 夹角
included angle 线性规划
linear programming 约束条件
目标函数
可行域
最优解
圆锥曲线
曲线
坐标法
解析几何
笛卡儿
标准方程
一般方程
参数方程
参数
圆锥曲线
椭圆
焦点
焦距
长轴
短轴
离心率
双曲线
实轴
虚轴
渐近线
抛物线
准线
constraint condition objective function feasible region optimal solution curve
method of coordinate analytic geometry Descartes
standard equation general equation parameter equation parameter point conic ellipse
focus, focal points focal length major axis minor axis eccentricity hyperbola real axis
imaginary axis asymptote parabola directrix
绪论
释药系统(drug delivery system,DDS)
中国药典(Chinese Pharmacopoeia,ChP)
美国药典(The United States Pharmacopoeia,USP) 美国国家处方集(The National Formulary,NF) 英国药典(British Pharmacopoeia,BP)
欧洲药典(European Pharmacopoeia,Ph.Eup)
国际药典(The International Pharmacopoeia,Ph.Int) 良好药品实验研究规范(Good Laboratory Practice,GLP) 良好药品生产规范(Good Manufacture Practice,GMP) 良好药品供应规范(Good Supply Practice,GSP) 良好药品临床试验规范(Good Clinical Practice,GCP) 分析质量管理(Analytical Quality Control,AQC)
第1章 药物的鉴别试验
药物的鉴别试验identification test
一般鉴别试验general identification test
专属鉴别试验specific identification test
灵敏度sensitivity
最低检出量minimum detectable quantity
最低检出浓度minimum detectable concentration
第2章 药物的杂质检查
巯基醋酸mercaptoacetic acid
古蔡氏Gutzeit
二乙基二硫代氨基甲酸银siliver diethyldithio-carbamate
推荐阅读:
中英文刀具词汇对照表06-08
考研英语词汇之易混词汇05-23
简历词汇-职务05-26
汉语词汇层06-12
俄语骂人词汇06-20
展会英语词汇06-22
日常生活日语词汇05-27
刍议英语词汇教学05-27
英语作文词汇升级06-04
财经相关英语词汇06-05